MINI RC JET BOAT 200 MONO

Boat full Size with Stator and Nozzle 230x75x50mm
Boat Size without Stator and Nozzle 200x75x50mm
You need a 3D printer with a minimum print-high of 200mm.

Follow us on Youtube to get notice of a New Upload!

RC controlled Mini Jet Boat 200 Mono
RC controlled Mini Jet Boat 200 Twin
RC controlled Mini Jet Boat 300 Mono

Take this model, if you only need the Water Jet Drive
For beginners, i recommend to start with RC Jet Boat 200 Mono or the Jet Boat 300 Mono
For beginners, i recommend to start with RC Jet Boat 200 Mono or the Jet Boat 300 Mono

Video:

• 3D printed RC JET Boat V003
• 3D printed RC JET Boat with JET Drive – Testing Self-Righting
• 3D printed RC JET Boat with JET Drive – Assembly
• 3D printed RC JET Boat with JET Drive
• 3D printed RC JET Boat with JET Drive – Testing
• 3D Printed RC JET Boat with JET Drive – sunny day run
• RC Speed Boat – 3D printed Jet Drive Bodensee
• RC MiniMono Boat – 3D printed 18mm Jet Drive
• RC MiniMono Boat – 3D printed Jet Drive UNDERWATER!
• 3D printed RC JET Boat with JET Drive – Electronics
• How to Replace Brushless Motor Shaft

Partlist

• 6x screw headless M2x3mm (propeller, servorhorn)
• 6x screw inbus M2x8mm (3x jet nozzle, 1x oil)
• 10x screw inbus M2x6mm (4x cover, 2x servo, 2x electronic, 2x motor)
• 2x screw inbus M1.6x5mm
• 6x insert M2x3mm heating brass insert, 4x cover, 2x electronic mount
• 1x seal Moosgummi Foam rubber cord 2x200mm
• 2x battery 18650 3400mah 3.7V or 18350 1500mah 3.7V
• 1x balancing cable 500 mm RC Servo cable
• 1x drive longer motor shaft 2x30mm
• 1x drive rod 2x100mm
• 1x drive shaft coupling, motor 2mm to rod 2mm
• 1x drive Brass bearing 52B 2.05x5x2.4mm, OD 5mm or MR25ZZ (4.50€)
• 1x servo 2g
• 1x servo rod 1mm, ca. 100mm
• 1x servo brass tube OD 2mm, ID 1mm (servo rod), Length 10mm
• 1x drive jet bearing, brass tube OD 3mm, ID 2mm (drive rod Length 3mm, servo rod Length 10mm)
• 1x Battery Lipo Charger iMAX B6 charger

Brushless Motor

• 1x drive motor DYS BE1806 2300KV orother motors also possible, diameter max. 23mm, length ca. 18mm, screws 16mm
• 1x drive esc Emax 20A BLHELI ESC or
• 1x drive esc Littlebee 20A ESC and 1x Recom R-785.0-0.5

Brushed Motor

• 2x screw inbus M2x4mm (2x motor)
• 1x drive Brushed motor 180
• 1x drive Brushed ESC 20A

My RC Controller (example)

• 1x Transmitter FrSky Taranis X9D Plus 2.4G
• 1x Receiver Mini Frsky D8 2.4G 4CH

or

• 1x Transmitter FLYSKY FS-i6X i6X 2.4GHz
• 1x Receiver Flysky i6 i6X i6S

Is it waterproof … YES, it is!

• Watch the video RC MiniMono Boat – 3D printed Jet Drive UNDERWATER! After that, there was no water in it!
• If your print of the hull is good, it should be waterproof. But, if you want to be safe, you could still paint it with a thin layer of car clear coat. I tried both variants and it works very well.
• The drive shaft of the boat is sealed between two plain bearings with a lubricating seal.
• The cover is sealed with a 2mm cord of foam rubber or with a 3d printed flex seal

Additional 3D Models:

• Cover Self-Righting
• Trim Tabs
• IKEA Transport Box
• Propeller 20mm 3 Blades
• Motor Coupling
• Boat Holder/ Stand

Object License – Standard Digital File Store License

• Remixing Not Allowed
• Commercial Use Not Allowed
• Add Credits To Designer When Sharing Links, Photos and Videos of Objects

 

slicer: cura (please take cura, Don’t take slic3r!)

• Material: PLA
• Nozzle: 0.4mm
• Infill Before Walls: No !!! Important !!!
• Outer Before Inner Walls: Yes !!! Important !!!
• wall: 3 Perimeter
• support: only for cover
• Optimize Wall Printing Order: Yes
• Fill Gabs Between Walls: No
• infill: 15
• Infill Travel Optimization: Yes
• adaptive layers: Yes with Layer: 0.15 to 0.20mm

Not to fast! Print the parts with about 30mm/s, to get a good layer connection. (It depends on the quality of your printer)
not to hot, because of dropping nozzle PLA 205*C